Remote Access to ReadyNAS with ZeroTier One

I recently purchased a diskless ReadyNAS 104 device from Netgear and filled it with a trio of WD Red 3 TB drives for my personal file storage. In this configuration, the NAS has a capacity of approximately 6 TB (one of the disks is used for parity), and houses backups of my files, photos, and home videos.

But, considering the device is attached to my apartment’s WiFi network, it’s not so useful outside of the premises. Netgear provides a client application called “ReadyNAS Remote”, which provides remote access to the NAS device presumably by relaying your traffic through one of their servers. However, this can be slow and potentially a security concern. As an alternative, I compiled ZeroTier One, a mesh VPN, to connect to my NAS remotely.

ZeroTier One is an open source mesh VPN software similar to N2N or Tinc. However, unlike N2N or Tinc, ZeroTier provides easy to use client applications to configure the network and handles both authentication and network management for you. This is similar to how LogMeIn Hamachi behaves, which also provides a web interface for creating networks and approving clients.

Registering for ZeroTier

ZeroTier’s client software is open source, though they do provide a premium service for free that allows you to connect more than 10 clients to a private network. However, if you’d like to run a private network with more than 10 clients for free, you can still do so by running the software on your own servers1.

Once you register for ZeroTier on their website, choose a name for your network and register it. After you’ve registered the network, you’ll see some configuration options:

ZeroTier One Admin Panel

Ensure that the “Private Network” box is checked (it is by default), and go ahead and select “Have ZeroTier Assign IPv4 Addresses”. This will allow ZeroTier to essentially act like a DHCP server for your VPN network. Any netblock can be used– it’s all based on your preference and whether any networks you use already use the netblock.

Installing the ZeroTier Client

The VPN clients for Mac and Windows are fairly straightforward to install. You may go ahead and install the clients onto the machines you wish to access the NAS from. Once the clients are installed, simply enter the network ID (as seen in the administration panel) into the text box in the bottom right hand corner of the ZeroTier window and click the plus.

You will see an “Access Denied” message once you’ve added the network because you must authorize the client from the web admin page. Go ahead and go so by checking the box next to the new client listed in your admin panel under the network you created. You may also want to give the client a descriptive name so you may identify it later.

ZeroTier Mac Client

The client doesn’t have much to configure– most of the configuration, such as static IP address assignments, are done from the ZeroTier administration interface.

Compiling ZeroTier One for ReadyNAS

The ReadyNAS 102 and 104 are ARM devices running a lightweight version of Debian Linux. However, currently ZeroTier doesn’t provide an ARM download for the client, so we must compile it ourselves. First, you must enable the SSH service from your ReadyNAS administration console. This can be found under “System” > “Settings”.

ReadyNAS Services

Once SSH is enabled, you can login to your NAS as the “root” user with the same password that’s set for the “admin” user on the front end. We’ll need to add some software to compile ZeroTier– namely, Git and the build tools. This can be done with a couple commands:

Once this is completed, we’ll need to get the source code for the ZeroTier client.

The main branch of the ZeroTier source code repository is a little old and doesn’t have some fixes required for ARM devices, and we must use the adamierymenko-dev branch. The below commands point to the specific commit I compiled for my ReadyNAS:

After the branch is checked out, you can run make in the ZeroTier One directory to compile the binaries. This will take a couple minutes because the ARM processor on the ReadyNAS is quite slow compared to a typical x86 desktop.

Once the software is compiled, you’ll have a couple binaries in the ZeroTier directory: zerotier-cli, zerotier-idtool, and zerotier-one. The two most important tools are zerotier-cli and zerotier-one. The latter is the service that runs to connect to the ZeroTier network and your other clients, while the former controls the service and commands it to join and leave networks.

You probably want to move the binaries to another location that isn’t the temporary directory:

After this is done, you can launch the ZeroTier service in the background:

We also want to run the ZeroTier service at boot and stop it before shutdown. This can be done by creating a new file called /etc/init.d/zerotier-one with the following contents:

Additionally, the script must be made executable:

Once this is done, you can run update-rc.d zerotier-one defaults to run the script and boot and shutdown. You can also run service zerotier-one start and service zerotier-one stop to start and stop the service.

Configuring ZeroTier

Now that you have compiled the ZeroTier service for your ReadyNAS system, you can run the CLI to join your NAS to your network. Documentation for the CLI is provided on ZeroTier’s GitHub Wiki, but the command to join a network is simple:

Simply replace “” with your own network ID as listed in the ZeroTier admin console, and you should see the new client pop up in the web interface. Simply approve your NAS’s join request and you’re finished.

You can also set a custom IP address for your NAS by clicking the edit icon in the “Assigned Addresses” column of the client list. Enter an IP address, and after a minute your ReadyNAS should be usable at your custom address.

ZeroTier Custom IP Address

Now you can visit the IP address in your web browser to view the admin console of your ReadyNAS device, or connect to AFP/SMB/NFS. This same IP address will work regardless of whether you’re on the same physical network (or a different one) as your NAS. Additionally, because ZeroTier is a mesh VPN, your traffic will also take the shortest route possible, which is often a direct connection from your computer to your NAS. If you are behind a strict firewall, ZeroTier’s supernodes will route your traffic between your devices for you, though this is unlikely to happen given the number of firewall-punching techniques embedded in the VPN software.

So far, the ARM based device has proved plenty capable and for a significantly lower price than most other NAS systems would come out to2. Combined with ZeroTier and CrashPlan to backup the critical data, the ReadyNAS 104 is a great little home/small business-class NAS that allows you to access your files from anywhere.


  1. The software is open source, but lacks documentation and is not trivial to setup. Additionally, you may also be required to run “supernodes”, which is simply a client that is used to relay traffic between two devices on a strictly firewalled network. The software for a “supernode” is the same as any other client, but usually it is run on a VPS or other server. 
  2. Amazon had a sale of the ReadyNAS 104 for ~$200, which is a good $60 off of what it is now. 

Subscribe to my mailing list

Get my latest posts delivered directly to your inbox